Eniun PC Lab is an online PC assembly simulator with a 3D workshop. In your browser, you can assemble a PC, upgrade its components and practice maintenance with step-by-step instructions, connection details and tips for a real computer.
1. Recommended order: first the motherboard, then the case
We recommend doing Motherboard assembly first and then
Installing components in the case. That way you follow the process from
preparing the motherboard to closing the computer. You can choose a different order: both labs are
open access and you do not have to finish the first to enter the second. In the case lab,
the CPU, RAM, M.2 SSD and CPU cooler are already installed on the motherboard.
Recommended device: We recommend using Eniun PC Lab on a laptop or desktop computer. Assembly needs screen space; on phones and tablets, some actions may be difficult or may not work properly.
You can click or drag the parts, depending on the action shown. In the case lab you can rotate and zoom the view; the close-ups help you recognize connector guides, contacts and their orientation.
2. How the workshop works
- Each lab is divided into short steps, with a clear prompt showing what to do next.
- If you choose the wrong part, slot or orientation, the simulator warns you and explains the
mistake.
- The help panels show how it is done on a real computer: part orientation, tips and
precautions.
- Your progress is saved in this browser: you can leave a lab and continue later.
- The explanations for each step let you check technical information while you assemble.
3. PC assembly and maintenance labs
Assemble a PC, install upgrades and practice maintenance tasks.
1. Motherboard assembly
You work on an ASUS PRIME B760-PLUS D4 motherboard on the bench, before fitting it in the case, following the
instructions in its manual:
- Prepare the workstation with the anti-static mat and a grounded wrist strap.
- Install the processor in the LGA1700 socket: open the lever, position it according to its orientation and close the
retention mechanism.
- Install two DDR4 RAM modules in the recommended slots for dual channel.
- Insert an M.2 NVMe SSD and secure it with its screw and a Phillips screwdriver.
- Fit the CPU cooler, secure its mounts in an alternating pattern and connect the fan to CPU_FAN.
Start motherboard assemblyStep by step, with explanations and help.→
2. Installing components in the PC case
The motherboard prepared in the previous lab is installed in an ATX chassis:
- Check that the chassis standoffs line up with the holes in the motherboard.
- Insert the motherboard with the rear ports facing their opening, line it up and rest it on the
standoffs.
- Secure the motherboard with its screws and the screwdriver.
- Place the ATX power supply in its bay and screw it to the chassis.
- Connect the 24-pin ATX and 8-pin EPS (4+4) power cables.
- Connect POWER SW, RESET SW, POWER LED and HDD LED, observing the polarity of the indicators.
- Connect the front-panel USB 3.0, USB 2.0 and HD AUDIO, and the rear fan.
- Install and secure the graphics card in PCI Express x16 and connect its 6-pin PCIe power cable.
- Route and secure the cables, leaving some slack and keeping the fans clear.
- Fit the side panel and tighten its two thumbscrews.
Start case assemblyAssembly, internal connections, graphics card, cabling and closing up.→
The lab runs through to closing the case. The PC stays disconnected from mains power during assembly.
3. Replacing thermal paste
On the assembled motherboard, you replace the processor’s thermal paste, with its stock cooler:
- Unplug the fan from CPU_FAN, turn the four push pins and lift the cooler straight up, without yanking it.
- Clean the old paste off the processor and the cooler base, each with its own lint-free wipe and isopropyl alcohol.
- Apply a pea-sized dot of new paste in the centre of the processor.
- Lower the cooler straight down and fasten the push pins in a diagonal pattern.
- Plug the fan back into CPU_FAN.
Start replacing the thermal pasteRemoval, cleaning, new paste and refitting the cooler.→
4. Installing expansion cards
Install a Wi‑Fi and Bluetooth card and connect its antennas and internal cable.
- Remove the side panel and locate a free PCIe x1 slot.
- Remove the slot cover at the back of the case.
- Insert the card and secure it to the case with a screw.
- Screw the antennas onto the card’s external connectors.
- Connect the internal Bluetooth cable to a free USB 2.0 header.
Start installing the expansion card→
5. Upgrade PC storage
Install a hard drive, a SATA SSD and an M.2 SSD.
- Place the 3.5-inch hard drive in the cage and secure it with its screws.
- Secure the 2.5-inch SATA SSD to its mount.
- Connect each SATA drive to a different data port on the motherboard.
- Connect SATA power from the power supply to both drives.
- Insert the M.2 SSD into the free slot and fasten it at its mounting point.
Start upgrading storage→
6. Install PC fans
Mount and connect a front fan.
- Remove the side panel to reach the inside of the case.
- Place the front fan so that it draws air into the case.
- Secure the fan with its screws.
- Align the guide and plug the four-pin cable into CHA_FAN2.
- Refit the side panel.
Start installing the fan→
7. Test a power supply
Start it with a jumper, measure it with a multimeter and check it with a tester.
- Fit the jumper between PS_ON# and ground with the power supply off and unplugged, then check startup.
- Set the multimeter to measure DC voltage and check the +12 V output.
- Turn off and unplug the power supply before removing the jumper, then measure the +5VSB standby voltage.
- Connect the 24-pin ATX and EPS 4+4 cables to the tester with the power supply off and unplugged.
- Interpret the voltage and Power Good (PG) readings, then turn off and unplug the power supply.
Start testing the power supply→
4. What you will have practiced by the end
The assembly order, component orientation and the difference between power, data and signal
connectors. You will have prepared the motherboard, secured the components to the chassis and routed the cables before
closing the panel. The simulator keeps your progress in each lab in this browser.
5. Assessments with interactive tests
Each practice has its own assessment: an interactive test to check what you have learned. These are the tests available; you can also find them in the Assessments section of the menu.
- They combine theory questions with hands-on exercises solved on the board itself: placing parts, connecting them and putting steps in order.
- When you finish you get a score out of 10, with the correction of each question and an explanation so you can learn from mistakes.
- You can retake the test as many times as you like, with no attempt limit.
- If you pass the test with at least 7/10, you can download your Eniun PC Lab certificate.
The best approach is to do the matching practice first and then its assessment.
Test: motherboard and componentsShow that you can install the CPU, RAM, M.2 SSD and CPU cooler.→
Test: PC case connectorsCheck that you can install the motherboard, power supply and graphics card in the case and connect their cables.→
Test: thermal pasteCheck that you know why, when and how thermal paste is replaced: types, safety, cleaning, amount and mounting.→
Test: expansion cardsRecognise cards and slots, match Wi‑Fi and Bluetooth to their connections and check that an installation is safe.→
Test: PC storageTell drives and connections apart, choose a free port and spot problems without putting data at risk.→
Test: PC fansRecognise the connector, choose a header and match cooling systems to how they work.→
Test: testing a power supplyPlace the jumper, choose the multimeter range and read the voltages and the tester screen.→
See the assessmentsTests scored out of 10 with a downloadable certificate.→
6. Who it is for
For students starting to learn PC assembly and maintenance, for example in IT vocational
training; for teachers who want to practice it in class before touching real hardware; and for anyone
who wants to know how a PC is put together.
The simulator does not replace a real workshop: it helps you understand each operation before doing it with real parts.
When you build a real computer, always check your motherboard manual.
Keep practicing
We'll email you when we publish a new Eniun PC Lab lab.