Installing components in the PC case is the second lab in Eniun PC Lab, an educational PC assembly simulator. It continues with the ASUS PRIME B760-PLUS D4 prepared in the previous lab: the processor, the two RAM modules, the M.2 SSD and the CPU cooler are already installed.
We recommend finishing Motherboard assembly first. That way you follow the build from the preparation of its components. You can start here directly if you prefer: it is not an access requirement.
How it works
- The part is already picked up: in each step, the part or cable you need appears selected, so you don't have to click it first.
- Click or drag: click the destination marked in orange and the part goes there by itself, or drag it and drop it there. Both ways work, except for the graphics card and the side panel, which you just click.
- Screws: click the indicated point or drag the screwdriver to it.
- See the case from another angle: drag the background to rotate or pan the view and use the mouse wheel to zoom in. On a touch screen, use two fingers to move and zoom.
- Prompts: the panel on the right tells you what to do and the orange marks show where. If you make a mistake, a message explains why.
- Arrows: use the ones at the bottom to go back a step or return to one you already did. The blue bar at the top shows your progress.
We recommend using Eniun PC Lab on a laptop or desktop computer. Assembly needs screen space; on phones and tablets, some actions may be difficult or may not work properly.
Your progress is saved in this browser.
Components in this lab
- ASUS PRIME B760-PLUS D4 motherboard. With the CPU, 2 RAM modules, M.2 SSD and CPU cooler already installed.
- 550 W ATX power supply. Orientation, placement and mounting.
- 24-pin ATX and 8-pin EPS (4+4) connections. Identifying them and connecting them to the motherboard.
- Front-panel buttons and indicators. POWER SW, RESET SW, HDD LED, POWER LED, USB and HD AUDIO.
- 120 mm rear fan. Already secured to the case. Four-contact PWM connection to CHA_FAN1.
- ASUS TUF GTX 1650 SUPER graphics card. Placement in PCIEX16, mounting and 6-pin PCIe power.
What you will learn
- Check the chassis standoffs and how they line up with the motherboard mounting holes.
- Point the input and output ports toward the rear opening of the chassis.
- Insert the motherboard with a guided movement, line it up and rest it on the standoffs.
- Secure the motherboard to the chassis with the screws and screwdriver.
- Install and secure the power supply and tell apart its 24-pin ATX and EPS 4+4 cables to connect them to the motherboard.
- Connect POWER SW, RESET SW and the HDD LED and POWER LED indicators, observing the polarity of the indicators.
- Connect USB, HD AUDIO and the rear fan to their matching headers.
- Install and secure the graphics card and connect its 6-pin PCIe power.
- Route the cables and close the case with the side panel and its thumbscrews.
Before placing the motherboard
Check the standoffs: they must line up with the holes in the motherboard and none should be left over underneath. They keep the motherboard raised so it doesn't rest directly on the metal. Hold the assembly by the edges of the motherboard.
Work with the computer unplugged and keep your precautions against electrostatic discharge, such as the grounded anti-static wrist strap from the motherboard lab: they are still needed when installing components in the case.
Order of this lab
- Install the motherboard. Check the standoffs, orient the motherboard, insert it through the open side and line up its holes with the supports before seating it.
- Secure the motherboard. Once it is resting and lined up, use the screws and screwdriver. Tighten until firm, without forcing.
- Install the power supply. Drag the power supply to the lower bay. The simulator orients it toward this case's vent; then secure it with four screws.
- Connect the power. Identify the 24-pin ATX cable and the 8-pin EPS (4+4) cable, and connect them to their inputs on the motherboard with the latch lined up.
- Connect the front panel. Connect the power and reset buttons and the two indicators to PANEL. The LEDs have a positive and a negative.
- Connect front USB and audio. Line up the USB 3.0, USB 2.0 and HD AUDIO guides with their inputs on the motherboard.
- Connect the rear fan. The fan is already secured to the case. Connect its four-contact PWM cable to CHA_FAN1.
- Install the graphics card. Remove the matching rear covers, seat the ASUS TUF GTX 1650 SUPER in PCIEX16, secure it to the chassis and connect the 6-pin block of the PCIe 6+2 cable.
- Route the cables. Click any of the indicated bundles to gather and secure them, leaving slack and the blades clear.
- Close the case. Slide the side panel into its guides and tighten its two rear thumbscrews.
This is the simulator's path. For a real computer, check the motherboard, chassis and power supply manuals; the assembly order and conditions depend on the computer.
The case and some volumes are simplified representations for educational purposes.
Assessment: PC case connectors test
When you finish the lab you can check what you have learned with a test on the same motherboard: its 2D photo, the edge with its ports, the graphics card bracket and a diagram of the case. It does not repeat the lab steps: it checks that you know why each thing is done.
There are 9 questions with a score out of 10. If you get a question right first time you score all its points, and half after one mistake; if you view the solution, that question scores nothing. Attempts are unlimited and, from 7 upwards, you can download a certificate.
Go to the PC case connectors test
Your progress is saved only in this browser and is not sent to any server. Privacy and cookies